'66 Deluxe

WideFive
Posts: 1234
Joined: Tue Dec 16, 2008 6:00 pm

Re: '66 Deluxe

Post by WideFive » Sat Nov 09, 2019 8:41 am

wwebner wrote:
Sat Nov 09, 2019 7:32 am
Is that JB weld on the cyl studs that are tapped through the case?
Permatex Ultra Black
"There is no restoration process that can give a car legitimacy equal to originality."

User avatar
Dual Port
Posts: 1132
Joined: Fri Apr 30, 2010 10:06 am

Re: '66 Deluxe

Post by Dual Port » Thu Dec 19, 2019 10:50 am

Been taking my time doing this as winter's here, took a couple of trips, worked on the Vette for a couple of weeks so now I'm back at it. I can't let Bill get ahead of me in the engine race.

I miked the crank bearings, they measured exactly the same as a new set I have on the shelf. I did change out the cam bearings, chucked up the cam and polished the journals with 1000 grit to a fine mirror finish.
PB160116.jpg
I had some machine work done on the cam for clearance for the stroker crank, new German lifters go on the cam with the gooey lube, clean the flanges with brakeclean and seal the case...
PB090002.JPG
PB090005.JPG
And it goes together, it spins as free as a bird.
PB090006.JPG
PB090015.JPG
Pics of the 92s next to a stock 85.5.
PB120019.JPG
PB120025.JPG
This engine only had a couple of thousand miles on it so it's like new inside. Not only did the mains show no wear but the rings are a tight .017" which is probably .015 or .016" actually. Spec is .012-.018" with a wear limit of .035" so they qualify as "new". There was zero carbon in the ring grooves, which is important for ring sealing. Jugs look perfect with hone marks still present so I'm not messing with them.
PB130042.JPG
Lube and install the rings, clean the case deck and base of the jugs with brakeclean and put a smear of RTV on the base of the jugs.
PB130046.JPG
Heads go on with a bit of Permatex under the lower washers to prevent oil seeping from the stud area.
PB130051.JPG
Bruce Amacker
'66 Deluxe Bus
'65 Standard Bus

User avatar
Dual Port
Posts: 1132
Joined: Fri Apr 30, 2010 10:06 am

Re: '66 Deluxe

Post by Dual Port » Thu Dec 19, 2019 11:39 am

Reseal the CB/JayCee adjustable pushrods.
PB140073.jpg
PB140079.JPG
As soon as I install heads and jugs I always pressure test or do a leakdown to verify the cylinders are tight. This is as tight as it gets, only a few % leakage on all 4.
PC030122.JPG

Install the Empi 1.5 quart sump. Like most Empi products the quality is a bit low so fitting is needed- figuring where the interference is which required grinding on both the case and the sump for clearance. I used a .0015" feeler gauge to verify the flange met all the way around, and RTV for the install. I put one on Bus 2 with Curil T that leaked.
PB160087.JPG
PB160095.JPG
PB160100.JPG
Stock screen and silicone gaskets on the sump plate.
PB160105.JPG
The intake runners on the manifold are larger than stock which means a stock boot won't fit. The neoprene hoses I installed before were "supposed" to be gasoline resistant, but I guess they were not. :( I wonder if the engine burped as it ingested these chunks of rubber a few years ago, I really don't remember.
PC190179.JPG
Getting parts painted for the upper stuff.
PC190173.JPG
Because it's a stroker the exhaust is short by about 5-6mm, modification needed.
PC170129.JPG
This is where I'm at, more to come.
PC190171.jpg
Bruce Amacker
'66 Deluxe Bus
'65 Standard Bus

User avatar
Six Volt
Posts: 3437
Joined: Mon Dec 15, 2008 7:25 am

Re: '66 Deluxe

Post by Six Volt » Fri Dec 20, 2019 1:21 pm

When you're further along, let's hear about that carb set up.
It's me, Sean
1957 Beetle Oval Sedan 36 Horse 6 volt
1959 Panel 40 Horse 6 volt

User avatar
Dual Port
Posts: 1132
Joined: Fri Apr 30, 2010 10:06 am

Re: '66 Deluxe

Post by Dual Port » Sun Dec 29, 2019 12:59 pm

The muffler looks pretty normal right?
PC230051a.jpg
Until you flip it over and see the surgical scars.
PC200004.JPG
First the baffles have to come out of #1 and 3 ports, this takes an acetylene torch and a screwdriver.
PC170139.JPG
It's hard to believe the engine can even breathe through these.
PC210012.jpg
Then cut open the back and see how the baffles are set up. I've done this a bunch of times and found that manufacturers use many different ways to baffle the exhaust. I made the center hole first, torched a big hole in the baffle tube, then used a borescope to look around more. I saw a divider plate near the ends so I had to cut twice more to be able to cut a big hole in those. In the end I didn't need to make the center hole but not a big deal.
PC200003.JPG
Because cutting the baffles out eliminates flow through the manifold heat tube, I weld a small diverter flap in the port to force exhaust under the carb. This makes the engine run MUCH better.
PC230073.JPG
Why do I go to all of this grief to modify a stock muffler? Because in the past I've bought numerous headers, performance mufflers and systems and was never happy with the first purchase. Either they're too loud, hang too low, don't fit my oil pump, or some other grief. On the Ghia I ended up buying several systems and ditching them to make my own. Even then I had to open the muffler up and modify the baffles to make it quieter- it was a big oval Magniflow can but had zero baffling inside. On the mufflers I've modified for my busses I'm happy with the noise level and flow. I'm sure they don't flow like a header but they're not obtrusively loud or resonant/buzzy, either.
The exhaust and trim is now done so it's time to prime the oil system. Because I use a filter pump I just pump oil into the filter outlet. I'm surprised how much oil it takes to pressurize the galleys, this gets the bearings wet before spinning the engine. There's no way around doing this without making a big f'ing mess. I use 0w-20 to prime the galleys and 0w-40 Mobil 1 in the sump.
PC290001.JPG
I then prime the pump and spin it over with the spark plugs out to get oil pressure without load on the rods. I quickly get 30+psi cranking. I did a compression test before putting the plugs in, all 4 are at 140psi. :D

It runs! And it runs great. The carb is a Zenith 32NDIX 2bbl that's used (in pairs) on early Porsche 356s. It sits on a vintage Deano manifold, probably from the 70's or 80's. I had Art Thraen build it about 10 years back, by the way the plugs look and the fuel economy, I'd say he nailed the jetting. I did run an (LM1?) on it when it was in the Ghia to verify fuel trim, it was great.

Ignore the dist, Sean asked me to try it for him. It will have a mechanical when it goes in the bus as my 32NDIX doesn't have ported vacuum. (BTW, the advance curve was surprisingly nice on that cheapy. I'll run it on my dist machine later for S&G but it was about 20° total mechanical starting about 1200 and all in about 2800 with about 8° vac) I had a Pertronix electronic in it before, it will probably go back in.

Oil pressure is 50psi all the time, I cranked the idle down to where it almost stalled and it was still 30 hot. Noise level is not bad but a little louder than my others because of the bigger displacement. Throttle response is RIGHT NOW.
PC290008.JPG
The best thing is that there are zero oil leaks! YEA!
Bruce Amacker
'66 Deluxe Bus
'65 Standard Bus

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest